Carlos Fenollosa
9 years ago
parent
c2a05935f8
commit
1a98cab56b
@ -0,0 +1 @@
|
||||
../19-interrupts-irqs/Makefile
|
||||
@ -0,0 +1,21 @@
|
||||
|
||||
Everything is now ready to test our hardware interrupts.
|
||||
|
||||
Timer
|
||||
-----
|
||||
|
||||
The timer is easy to configure. First we'll declare an `init_timer()` on `cpu/timer.h` and
|
||||
implement it on `cpu/timer.c`. It is just a matter of computing the clock frequency and
|
||||
sending the bytes to the appropriate ports.
|
||||
|
||||
## se printa gibberish, pq? mirar primero si se arregla con un kprint_int
|
||||
## yo tenia una funcion que printaba enteros??!!! pero al rever. hacerla ahora bien y
|
||||
## en el proximo episodio limpiar codigo y crear una libc
|
||||
|
||||
|
||||
Finally, go back to the `kernel/kernel.c` and do two things. Enable interrupts again
|
||||
(very important!) and then initialize the timer interrupt.
|
||||
|
||||
Go `make run` and you'll see the clock ticking! Unfortunately we are not printing the correct values
|
||||
on screen, so we'll go ahead to `drivers/screen.c` and add a new `kprint_int()` method, also declaring
|
||||
it on `drivers/screen.h`
|
||||
@ -0,0 +1 @@
|
||||
../19-interrupts-irqs/boot
|
||||
@ -0,0 +1,17 @@
|
||||
#include "idt.h"
|
||||
#include "../kernel/util.h"
|
||||
|
||||
void set_idt_gate(int n, u32 handler) {
|
||||
idt[n].low_offset = low_16(handler);
|
||||
idt[n].sel = KERNEL_CS;
|
||||
idt[n].always0 = 0;
|
||||
idt[n].flags = 0x8E;
|
||||
idt[n].high_offset = high_16(handler);
|
||||
}
|
||||
|
||||
void set_idt() {
|
||||
idt_reg.base = (u32) &idt;
|
||||
idt_reg.limit = IDT_ENTRIES * sizeof(idt_gate_t) - 1;
|
||||
/* Don't make the mistake of loading &idt -- always load &idt_reg */
|
||||
__asm__ __volatile__("lidtl (%0)" : : "r" (&idt_reg));
|
||||
}
|
||||
@ -0,0 +1,39 @@
|
||||
#ifndef IDT_H
|
||||
#define IDT_H
|
||||
|
||||
#include "types.h"
|
||||
|
||||
/* Segment selectors */
|
||||
#define KERNEL_CS 0x08
|
||||
|
||||
/* How every interrupt gate (handler) is defined */
|
||||
typedef struct {
|
||||
u16 low_offset; /* Lower 16 bits of handler function address */
|
||||
u16 sel; /* Kernel segment selector */
|
||||
u8 always0;
|
||||
/* First byte
|
||||
* Bit 7: "Interrupt is present"
|
||||
* Bits 6-5: Privilege level of caller (0=kernel..3=user)
|
||||
* Bit 4: Set to 0 for interrupt gates
|
||||
* Bits 3-0: bits 1110 = decimal 14 = "32 bit interrupt gate" */
|
||||
u8 flags;
|
||||
u16 high_offset; /* Higher 16 bits of handler function address */
|
||||
} __attribute__((packed)) idt_gate_t ;
|
||||
|
||||
/* A pointer to the array of interrupt handlers.
|
||||
* Assembly instruction 'lidt' will read it */
|
||||
typedef struct {
|
||||
u16 limit;
|
||||
u32 base;
|
||||
} __attribute__((packed)) idt_register_t;
|
||||
|
||||
#define IDT_ENTRIES 256
|
||||
idt_gate_t idt[IDT_ENTRIES];
|
||||
idt_register_t idt_reg;
|
||||
|
||||
|
||||
/* Functions implemented in idt.c */
|
||||
void set_idt_gate(int n, u32 handler);
|
||||
void set_idt();
|
||||
|
||||
#endif
|
||||
@ -0,0 +1,425 @@
|
||||
; Defined in isr.c
|
||||
[extern isr_handler]
|
||||
[extern irq_handler]
|
||||
|
||||
; Common ISR code
|
||||
isr_common_stub:
|
||||
; 1. Save CPU state
|
||||
pusha ; Pushes edi,esi,ebp,esp,ebx,edx,ecx,eax
|
||||
mov ax, ds ; Lower 16-bits of eax = ds.
|
||||
push eax ; save the data segment descriptor
|
||||
mov ax, 0x10 ; kernel data segment descriptor
|
||||
mov ds, ax
|
||||
mov es, ax
|
||||
mov fs, ax
|
||||
mov gs, ax
|
||||
|
||||
; 2. Call C handler
|
||||
call isr_handler
|
||||
|
||||
; 3. Restore state
|
||||
pop eax
|
||||
mov ds, ax
|
||||
mov es, ax
|
||||
mov fs, ax
|
||||
mov gs, ax
|
||||
popa
|
||||
add esp, 8 ; Cleans up the pushed error code and pushed ISR number
|
||||
sti
|
||||
iret ; pops 5 things at once: CS, EIP, EFLAGS, SS, and ESP
|
||||
|
||||
; Common IRQ code. Identical to ISR code except for the 'call'
|
||||
; and the 'pop ebx'
|
||||
irq_common_stub:
|
||||
pusha
|
||||
mov ax, ds
|
||||
push eax
|
||||
mov ax, 0x10
|
||||
mov ds, ax
|
||||
mov es, ax
|
||||
mov fs, ax
|
||||
mov gs, ax
|
||||
call irq_handler ; Different than the ISR code
|
||||
pop ebx ; Different than the ISR code
|
||||
mov ds, bx
|
||||
mov es, bx
|
||||
mov fs, bx
|
||||
mov gs, bx
|
||||
popa
|
||||
add esp, 8
|
||||
sti
|
||||
iret
|
||||
|
||||
; We don't get information about which interrupt was caller
|
||||
; when the handler is run, so we will need to have a different handler
|
||||
; for every interrupt.
|
||||
; Furthermore, some interrupts push an error code onto the stack but others
|
||||
; don't, so we will push a dummy error code for those which don't, so that
|
||||
; we have a consistent stack for all of them.
|
||||
|
||||
; First make the ISRs global
|
||||
global isr0
|
||||
global isr1
|
||||
global isr2
|
||||
global isr3
|
||||
global isr4
|
||||
global isr5
|
||||
global isr6
|
||||
global isr7
|
||||
global isr8
|
||||
global isr9
|
||||
global isr10
|
||||
global isr11
|
||||
global isr12
|
||||
global isr13
|
||||
global isr14
|
||||
global isr15
|
||||
global isr16
|
||||
global isr17
|
||||
global isr18
|
||||
global isr19
|
||||
global isr20
|
||||
global isr21
|
||||
global isr22
|
||||
global isr23
|
||||
global isr24
|
||||
global isr25
|
||||
global isr26
|
||||
global isr27
|
||||
global isr28
|
||||
global isr29
|
||||
global isr30
|
||||
global isr31
|
||||
; IRQs
|
||||
global irq0
|
||||
global irq1
|
||||
global irq2
|
||||
global irq3
|
||||
global irq4
|
||||
global irq5
|
||||
global irq6
|
||||
global irq7
|
||||
global irq8
|
||||
global irq9
|
||||
global irq10
|
||||
global irq11
|
||||
global irq12
|
||||
global irq13
|
||||
global irq14
|
||||
global irq15
|
||||
|
||||
; 0: Divide By Zero Exception
|
||||
isr0:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 0
|
||||
jmp isr_common_stub
|
||||
|
||||
; 1: Debug Exception
|
||||
isr1:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 1
|
||||
jmp isr_common_stub
|
||||
|
||||
; 2: Non Maskable Interrupt Exception
|
||||
isr2:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 2
|
||||
jmp isr_common_stub
|
||||
|
||||
; 3: Int 3 Exception
|
||||
isr3:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 3
|
||||
jmp isr_common_stub
|
||||
|
||||
; 4: INTO Exception
|
||||
isr4:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 4
|
||||
jmp isr_common_stub
|
||||
|
||||
; 5: Out of Bounds Exception
|
||||
isr5:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 5
|
||||
jmp isr_common_stub
|
||||
|
||||
; 6: Invalid Opcode Exception
|
||||
isr6:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 6
|
||||
jmp isr_common_stub
|
||||
|
||||
; 7: Coprocessor Not Available Exception
|
||||
isr7:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 7
|
||||
jmp isr_common_stub
|
||||
|
||||
; 8: Double Fault Exception (With Error Code!)
|
||||
isr8:
|
||||
cli
|
||||
push byte 8
|
||||
jmp isr_common_stub
|
||||
|
||||
; 9: Coprocessor Segment Overrun Exception
|
||||
isr9:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 9
|
||||
jmp isr_common_stub
|
||||
|
||||
; 10: Bad TSS Exception (With Error Code!)
|
||||
isr10:
|
||||
cli
|
||||
push byte 10
|
||||
jmp isr_common_stub
|
||||
|
||||
; 11: Segment Not Present Exception (With Error Code!)
|
||||
isr11:
|
||||
cli
|
||||
push byte 11
|
||||
jmp isr_common_stub
|
||||
|
||||
; 12: Stack Fault Exception (With Error Code!)
|
||||
isr12:
|
||||
cli
|
||||
push byte 12
|
||||
jmp isr_common_stub
|
||||
|
||||
; 13: General Protection Fault Exception (With Error Code!)
|
||||
isr13:
|
||||
cli
|
||||
push byte 13
|
||||
jmp isr_common_stub
|
||||
|
||||
; 14: Page Fault Exception (With Error Code!)
|
||||
isr14:
|
||||
cli
|
||||
push byte 14
|
||||
jmp isr_common_stub
|
||||
|
||||
; 15: Reserved Exception
|
||||
isr15:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 15
|
||||
jmp isr_common_stub
|
||||
|
||||
; 16: Floating Point Exception
|
||||
isr16:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 16
|
||||
jmp isr_common_stub
|
||||
|
||||
; 17: Alignment Check Exception
|
||||
isr17:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 17
|
||||
jmp isr_common_stub
|
||||
|
||||
; 18: Machine Check Exception
|
||||
isr18:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 18
|
||||
jmp isr_common_stub
|
||||
|
||||
; 19: Reserved
|
||||
isr19:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 19
|
||||
jmp isr_common_stub
|
||||
|
||||
; 20: Reserved
|
||||
isr20:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 20
|
||||
jmp isr_common_stub
|
||||
|
||||
; 21: Reserved
|
||||
isr21:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 21
|
||||
jmp isr_common_stub
|
||||
|
||||
; 22: Reserved
|
||||
isr22:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 22
|
||||
jmp isr_common_stub
|
||||
|
||||
; 23: Reserved
|
||||
isr23:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 23
|
||||
jmp isr_common_stub
|
||||
|
||||
; 24: Reserved
|
||||
isr24:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 24
|
||||
jmp isr_common_stub
|
||||
|
||||
; 25: Reserved
|
||||
isr25:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 25
|
||||
jmp isr_common_stub
|
||||
|
||||
; 26: Reserved
|
||||
isr26:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 26
|
||||
jmp isr_common_stub
|
||||
|
||||
; 27: Reserved
|
||||
isr27:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 27
|
||||
jmp isr_common_stub
|
||||
|
||||
; 28: Reserved
|
||||
isr28:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 28
|
||||
jmp isr_common_stub
|
||||
|
||||
; 29: Reserved
|
||||
isr29:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 29
|
||||
jmp isr_common_stub
|
||||
|
||||
; 30: Reserved
|
||||
isr30:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 30
|
||||
jmp isr_common_stub
|
||||
|
||||
; 31: Reserved
|
||||
isr31:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 31
|
||||
jmp isr_common_stub
|
||||
|
||||
; IRQ handlers
|
||||
irq0:
|
||||
cli
|
||||
push byte 0
|
||||
push byte 32
|
||||
jmp irq_common_stub
|
||||
|
||||
irq1:
|
||||
cli
|
||||
push byte 1
|
||||
push byte 33
|
||||
jmp irq_common_stub
|
||||
|
||||
irq2:
|
||||
cli
|
||||
push byte 2
|
||||
push byte 34
|
||||
jmp irq_common_stub
|
||||
|
||||
irq3:
|
||||
cli
|
||||
push byte 3
|
||||
push byte 35
|
||||
jmp irq_common_stub
|
||||
|
||||
irq4:
|
||||
cli
|
||||
push byte 4
|
||||
push byte 36
|
||||
jmp irq_common_stub
|
||||
|
||||
irq5:
|
||||
cli
|
||||
push byte 5
|
||||
push byte 37
|
||||
jmp irq_common_stub
|
||||
|
||||
irq6:
|
||||
cli
|
||||
push byte 6
|
||||
push byte 38
|
||||
jmp irq_common_stub
|
||||
|
||||
irq7:
|
||||
cli
|
||||
push byte 7
|
||||
push byte 39
|
||||
jmp irq_common_stub
|
||||
|
||||
irq8:
|
||||
cli
|
||||
push byte 8
|
||||
push byte 40
|
||||
jmp irq_common_stub
|
||||
|
||||
irq9:
|
||||
cli
|
||||
push byte 9
|
||||
push byte 41
|
||||
jmp irq_common_stub
|
||||
|
||||
irq10:
|
||||
cli
|
||||
push byte 10
|
||||
push byte 42
|
||||
jmp irq_common_stub
|
||||
|
||||
irq11:
|
||||
cli
|
||||
push byte 11
|
||||
push byte 43
|
||||
jmp irq_common_stub
|
||||
|
||||
irq12:
|
||||
cli
|
||||
push byte 12
|
||||
push byte 44
|
||||
jmp irq_common_stub
|
||||
|
||||
irq13:
|
||||
cli
|
||||
push byte 13
|
||||
push byte 45
|
||||
jmp irq_common_stub
|
||||
|
||||
irq14:
|
||||
cli
|
||||
push byte 14
|
||||
push byte 46
|
||||
jmp irq_common_stub
|
||||
|
||||
irq15:
|
||||
cli
|
||||
push byte 15
|
||||
push byte 47
|
||||
jmp irq_common_stub
|
||||
|
||||
@ -0,0 +1,140 @@
|
||||
#include "isr.h"
|
||||
#include "idt.h"
|
||||
#include "../drivers/screen.h"
|
||||
#include "../kernel/util.h"
|
||||
#include "../drivers/ports.h"
|
||||
|
||||
isr_t interrupt_handlers[256];
|
||||
|
||||
/* Can't do this with a loop because we need the address
|
||||
* of the function names */
|
||||
void isr_install() {
|
||||
set_idt_gate(0, (u32)isr0);
|
||||
set_idt_gate(1, (u32)isr1);
|
||||
set_idt_gate(2, (u32)isr2);
|
||||
set_idt_gate(3, (u32)isr3);
|
||||
set_idt_gate(4, (u32)isr4);
|
||||
set_idt_gate(5, (u32)isr5);
|
||||
set_idt_gate(6, (u32)isr6);
|
||||
set_idt_gate(7, (u32)isr7);
|
||||
set_idt_gate(8, (u32)isr8);
|
||||
set_idt_gate(9, (u32)isr9);
|
||||
set_idt_gate(10, (u32)isr10);
|
||||
set_idt_gate(11, (u32)isr11);
|
||||
set_idt_gate(12, (u32)isr12);
|
||||
set_idt_gate(13, (u32)isr13);
|
||||
set_idt_gate(14, (u32)isr14);
|
||||
set_idt_gate(15, (u32)isr15);
|
||||
set_idt_gate(16, (u32)isr16);
|
||||
set_idt_gate(17, (u32)isr17);
|
||||
set_idt_gate(18, (u32)isr18);
|
||||
set_idt_gate(19, (u32)isr19);
|
||||
set_idt_gate(20, (u32)isr20);
|
||||
set_idt_gate(21, (u32)isr21);
|
||||
set_idt_gate(22, (u32)isr22);
|
||||
set_idt_gate(23, (u32)isr23);
|
||||
set_idt_gate(24, (u32)isr24);
|
||||
set_idt_gate(25, (u32)isr25);
|
||||
set_idt_gate(26, (u32)isr26);
|
||||
set_idt_gate(27, (u32)isr27);
|
||||
set_idt_gate(28, (u32)isr28);
|
||||
set_idt_gate(29, (u32)isr29);
|
||||
set_idt_gate(30, (u32)isr30);
|
||||
set_idt_gate(31, (u32)isr31);
|
||||
|
||||
// Remap the PIC
|
||||
port_byte_out(0x20, 0x11);
|
||||
port_byte_out(0xA0, 0x11);
|
||||
port_byte_out(0x21, 0x20);
|
||||
port_byte_out(0xA1, 0x28);
|
||||
port_byte_out(0x21, 0x04);
|
||||
port_byte_out(0xA1, 0x02);
|
||||
port_byte_out(0x21, 0x01);
|
||||
port_byte_out(0xA1, 0x01);
|
||||
port_byte_out(0x21, 0x0);
|
||||
port_byte_out(0xA1, 0x0);
|
||||
|
||||
// Install the IRQs
|
||||
set_idt_gate(32, (u32)irq0);
|
||||
set_idt_gate(33, (u32)irq1);
|
||||
set_idt_gate(34, (u32)irq2);
|
||||
set_idt_gate(35, (u32)irq3);
|
||||
set_idt_gate(36, (u32)irq4);
|
||||
set_idt_gate(37, (u32)irq5);
|
||||
set_idt_gate(38, (u32)irq6);
|
||||
set_idt_gate(39, (u32)irq7);
|
||||
set_idt_gate(40, (u32)irq8);
|
||||
set_idt_gate(41, (u32)irq9);
|
||||
set_idt_gate(42, (u32)irq10);
|
||||
set_idt_gate(43, (u32)irq11);
|
||||
set_idt_gate(44, (u32)irq12);
|
||||
set_idt_gate(45, (u32)irq13);
|
||||
set_idt_gate(46, (u32)irq14);
|
||||
set_idt_gate(47, (u32)irq15);
|
||||
|
||||
set_idt(); // Load with ASM
|
||||
}
|
||||
|
||||
/* To print the message which defines every exception */
|
||||
char *exception_messages[] = {
|
||||
"Division By Zero",
|
||||
"Debug",
|
||||
"Non Maskable Interrupt",
|
||||
"Breakpoint",
|
||||
"Into Detected Overflow",
|
||||
"Out of Bounds",
|
||||
"Invalid Opcode",
|
||||
"No Coprocessor",
|
||||
|
||||
"Double Fault",
|
||||
"Coprocessor Segment Overrun",
|
||||
"Bad TSS",
|
||||
"Segment Not Present",
|
||||
"Stack Fault",
|
||||
"General Protection Fault",
|
||||
"Page Fault",
|
||||
"Unknown Interrupt",
|
||||
|
||||
"Coprocessor Fault",
|
||||
"Alignment Check",
|
||||
"Machine Check",
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
"Reserved",
|
||||
"Reserved"
|
||||
};
|
||||
|
||||
void isr_handler(registers_t r) {
|
||||
kprint("received interrupt: ");
|
||||
char s[3];
|
||||
int_to_ascii(r.int_no, s);
|
||||
kprint(s);
|
||||
kprint("\n");
|
||||
kprint(exception_messages[r.int_no]);
|
||||
kprint("\n");
|
||||
}
|
||||
|
||||
void register_interrupt_handler(u8 n, isr_t handler) {
|
||||
interrupt_handlers[n] = handler;
|
||||
}
|
||||
|
||||
void irq_handler(registers_t r) {
|
||||
/* If the irq involves the slave (IRQ > 7), send an EOI to it */
|
||||
if (r.int_no >= 40) port_byte_out(0xA0, 0x20);
|
||||
port_byte_out(0x20, 0x20); /* Send EOI to master */
|
||||
/* Handle the interrupt in a more modular way */
|
||||
if (interrupt_handlers[r.int_no] != 0) {
|
||||
isr_t handler = interrupt_handlers[r.int_no];
|
||||
handler(r);
|
||||
}
|
||||
}
|
||||
@ -0,0 +1,88 @@
|
||||
#ifndef ISR_H
|
||||
#define ISR_H
|
||||
|
||||
#include "types.h"
|
||||
|
||||
/* ISRs reserved for CPU exceptions */
|
||||
extern void isr0();
|
||||
extern void isr1();
|
||||
extern void isr2();
|
||||
extern void isr3();
|
||||
extern void isr4();
|
||||
extern void isr5();
|
||||
extern void isr6();
|
||||
extern void isr7();
|
||||
extern void isr8();
|
||||
extern void isr9();
|
||||
extern void isr10();
|
||||
extern void isr11();
|
||||
extern void isr12();
|
||||
extern void isr13();
|
||||
extern void isr14();
|
||||
extern void isr15();
|
||||
extern void isr16();
|
||||
extern void isr17();
|
||||
extern void isr18();
|
||||
extern void isr19();
|
||||
extern void isr20();
|
||||
extern void isr21();
|
||||
extern void isr22();
|
||||
extern void isr23();
|
||||
extern void isr24();
|
||||
extern void isr25();
|
||||
extern void isr26();
|
||||
extern void isr27();
|
||||
extern void isr28();
|
||||
extern void isr29();
|
||||
extern void isr30();
|
||||
extern void isr31();
|
||||
/* IRQ definitions */
|
||||
extern void irq0();
|
||||
extern void irq1();
|
||||
extern void irq2();
|
||||
extern void irq3();
|
||||
extern void irq4();
|
||||
extern void irq5();
|
||||
extern void irq6();
|
||||
extern void irq7();
|
||||
extern void irq8();
|
||||
extern void irq9();
|
||||
extern void irq10();
|
||||
extern void irq11();
|
||||
extern void irq12();
|
||||
extern void irq13();
|
||||
extern void irq14();
|
||||
extern void irq15();
|
||||
|
||||
#define IRQ0 32
|
||||
#define IRQ1 33
|
||||
#define IRQ2 34
|
||||
#define IRQ3 35
|
||||
#define IRQ4 36
|
||||
#define IRQ5 37
|
||||
#define IRQ6 38
|
||||
#define IRQ7 39
|
||||
#define IRQ8 40
|
||||
#define IRQ9 41
|
||||
#define IRQ10 42
|
||||
#define IRQ11 43
|
||||
#define IRQ12 44
|
||||
#define IRQ13 45
|
||||
#define IRQ14 46
|
||||
#define IRQ15 47
|
||||
|
||||
/* Struct which aggregates many registers */
|
||||
typedef struct {
|
||||
u32 ds; /* Data segment selector */
|
||||
u32 edi, esi, ebp, esp, ebx, edx, ecx, eax; /* Pushed by pusha. */
|
||||
u32 int_no, err_code; /* Interrupt number and error code (if applicable) */
|
||||
u32 eip, cs, eflags, useresp, ss; /* Pushed by the processor automatically */
|
||||
} registers_t;
|
||||
|
||||
void isr_install();
|
||||
void isr_handler(registers_t r);
|
||||
|
||||
typedef void (*isr_t)(registers_t);
|
||||
void register_interrupt_handler(u8 n, isr_t handler);
|
||||
|
||||
#endif
|
||||
@ -0,0 +1,27 @@
|
||||
#include "timer.h"
|
||||
#include "../drivers/screen.h"
|
||||
#include "isr.h"
|
||||
|
||||
u32 tick = 0;
|
||||
|
||||
static void timer_callback(registers_t regs) {
|
||||
tick++;
|
||||
kprint("Tick: ");
|
||||
kprint(tick);
|
||||
kprint("\n");
|
||||
}
|
||||
|
||||
void init_timer(u32 freq) {
|
||||
/* Install the function we just wrote */
|
||||
register_interrupt_handler(IRQ0, timer_callback);
|
||||
|
||||
/* Get the PIT value: hardware clock at 1193180 Hz */
|
||||
u32 divisor = 1193180 / freq;
|
||||
u8 low = (u8)(divisor & 0xFF);
|
||||
u8 high = (u8)( (divisor >> 8) & 0xFF);
|
||||
/* Send the command */
|
||||
port_byte_out(0x43, 0x36); /* Command port */
|
||||
port_byte_out(0x40, low);
|
||||
port_byte_out(0x40, high);
|
||||
}
|
||||
|
||||
@ -0,0 +1,8 @@
|
||||
#ifndef TIMER_H
|
||||
#define TIMER_H
|
||||
|
||||
#include "../kernel/util.h"
|
||||
|
||||
void init_timer(u32 freq);
|
||||
|
||||
#endif
|
||||
@ -0,0 +1,16 @@
|
||||
#ifndef TYPES_H
|
||||
#define TYPES_H
|
||||
|
||||
/* Instead of using 'chars' to allocate non-character bytes,
|
||||
* we will use these new type with no semantic meaning */
|
||||
typedef unsigned int u32;
|
||||
typedef int s32;
|
||||
typedef unsigned short u16;
|
||||
typedef short s16;
|
||||
typedef unsigned char u8;
|
||||
typedef char s8;
|
||||
|
||||
#define low_16(address) (u16)((address) & 0xFFFF)
|
||||
#define high_16(address) (u16)(((address) >> 16) & 0xFFFF)
|
||||
|
||||
#endif
|
||||
@ -0,0 +1,37 @@
|
||||
#include "ports.h"
|
||||
|
||||
/**
|
||||
* Read a byte from the specified port
|
||||
*/
|
||||
u8 port_byte_in (u16 port) {
|
||||
u8 result;
|
||||
/* Inline assembler syntax
|
||||
* !! Notice how the source and destination registers are switched from NASM !!
|
||||
*
|
||||
* '"=a" (result)'; set '=' the C variable '(result)' to the value of register e'a'x
|
||||
* '"d" (port)': map the C variable '(port)' into e'd'x register
|
||||
*
|
||||
* Inputs and outputs are separated by colons
|
||||
*/
|
||||
__asm__("in %%dx, %%al" : "=a" (result) : "d" (port));
|
||||
return result;
|
||||
}
|
||||
|
||||
void port_byte_out (u16 port, u8 data) {
|
||||
/* Notice how here both registers are mapped to C variables and
|
||||
* nothing is returned, thus, no equals '=' in the asm syntax
|
||||
* However we see a comma since there are two variables in the input area
|
||||
* and none in the 'return' area
|
||||
*/
|
||||
__asm__ __volatile__("out %%al, %%dx" : : "a" (data), "d" (port));
|
||||
}
|
||||
|
||||
u16 port_word_in (u16 port) {
|
||||
u16 result;
|
||||
__asm__("in %%dx, %%ax" : "=a" (result) : "d" (port));
|
||||
return result;
|
||||
}
|
||||
|
||||
void port_word_out (u16 port, u16 data) {
|
||||
__asm__ __volatile__("out %%ax, %%dx" : : "a" (data), "d" (port));
|
||||
}
|
||||
@ -0,0 +1,11 @@
|
||||
#ifndef PORTS_H
|
||||
#define PORTS_H
|
||||
|
||||
#include "../cpu/types.h"
|
||||
|
||||
unsigned char port_byte_in (u16 port);
|
||||
void port_byte_out (u16 port, u8 data);
|
||||
unsigned short port_word_in (u16 port);
|
||||
void port_word_out (u16 port, u16 data);
|
||||
|
||||
#endif
|
||||
@ -0,0 +1,139 @@
|
||||
#include "screen.h"
|
||||
#include "ports.h"
|
||||
#include "../kernel/util.h"
|
||||
|
||||
/* Declaration of private functions */
|
||||
int get_cursor_offset();
|
||||
void set_cursor_offset(int offset);
|
||||
int print_char(char c, int col, int row, char attr);
|
||||
int get_offset(int col, int row);
|
||||
int get_offset_row(int offset);
|
||||
int get_offset_col(int offset);
|
||||
|
||||
/**********************************************************
|
||||
* Public Kernel API functions *
|
||||
**********************************************************/
|
||||
|
||||
/**
|
||||
* Print a message on the specified location
|
||||
* If col, row, are negative, we will use the current offset
|
||||
*/
|
||||
void kprint_at(char *message, int col, int row) {
|
||||
/* Set cursor if col/row are negative */
|
||||
int offset;
|
||||
if (col >= 0 && row >= 0)
|
||||
offset = get_offset(col, row);
|
||||
else {
|
||||
offset = get_cursor_offset();
|
||||
row = get_offset_row(offset);
|
||||
col = get_offset_col(offset);
|
||||
}
|
||||
|
||||
/* Loop through message and print it */
|
||||
int i = 0;
|
||||
while (message[i] != 0) {
|
||||
offset = print_char(message[i++], col, row, WHITE_ON_BLACK);
|
||||
/* Compute row/col for next iteration */
|
||||
row = get_offset_row(offset);
|
||||
col = get_offset_col(offset);
|
||||
}
|
||||
}
|
||||
|
||||
void kprint(char *message) {
|
||||
kprint_at(message, -1, -1);
|
||||
}
|
||||
|
||||
|
||||
/**********************************************************
|
||||
* Private kernel functions *
|
||||
**********************************************************/
|
||||
|
||||
|
||||
/**
|
||||
* Innermost print function for our kernel, directly accesses the video memory
|
||||
*
|
||||
* If 'col' and 'row' are negative, we will print at current cursor location
|
||||
* If 'attr' is zero it will use 'white on black' as default
|
||||
* Returns the offset of the next character
|
||||
* Sets the video cursor to the returned offset
|
||||
*/
|
||||
int print_char(char c, int col, int row, char attr) {
|
||||
unsigned char *vidmem = (unsigned char*) VIDEO_ADDRESS;
|
||||
if (!attr) attr = WHITE_ON_BLACK;
|
||||
|
||||
/* Error control: print a red 'E' if the coords aren't right */
|
||||
if (col >= MAX_COLS || row >= MAX_ROWS) {
|
||||
vidmem[2*(MAX_COLS)*(MAX_ROWS)-2] = 'E';
|
||||
vidmem[2*(MAX_COLS)*(MAX_ROWS)-1] = RED_ON_WHITE;
|
||||
return get_offset(col, row);
|
||||
}
|
||||
|
||||
int offset;
|
||||
if (col >= 0 && row >= 0) offset = get_offset(col, row);
|
||||
else offset = get_cursor_offset();
|
||||
|
||||
if (c == '\n') {
|
||||
row = get_offset_row(offset);
|
||||
offset = get_offset(0, row+1);
|
||||
} else {
|
||||
vidmem[offset] = c;
|
||||
vidmem[offset+1] = attr;
|
||||
offset += 2;
|
||||
}
|
||||
|
||||
/* Check if the offset is over screen size and scroll */
|
||||
if (offset >= MAX_ROWS * MAX_COLS * 2) {
|
||||
int i;
|
||||
for (i = 1; i < MAX_ROWS; i++)
|
||||
memory_copy(get_offset(0, i) + VIDEO_ADDRESS,
|
||||
get_offset(0, i-1) + VIDEO_ADDRESS,
|
||||
MAX_COLS * 2);
|
||||
|
||||
/* Blank last line */
|
||||
char *last_line = get_offset(0, MAX_ROWS-1) + VIDEO_ADDRESS;
|
||||
for (i = 0; i < MAX_COLS * 2; i++) last_line[i] = 0;
|
||||
|
||||
offset -= 2 * MAX_COLS;
|
||||
}
|
||||
|
||||
set_cursor_offset(offset);
|
||||
return offset;
|
||||
}
|
||||
|
||||
int get_cursor_offset() {
|
||||
/* Use the VGA ports to get the current cursor position
|
||||
* 1. Ask for high byte of the cursor offset (data 14)
|
||||
* 2. Ask for low byte (data 15)
|
||||
*/
|
||||
port_byte_out(REG_SCREEN_CTRL, 14);
|
||||
int offset = port_byte_in(REG_SCREEN_DATA) << 8; /* High byte: << 8 */
|
||||
port_byte_out(REG_SCREEN_CTRL, 15);
|
||||
offset += port_byte_in(REG_SCREEN_DATA);
|
||||
return offset * 2; /* Position * size of character cell */
|
||||
}
|
||||
|
||||
void set_cursor_offset(int offset) {
|
||||
/* Similar to get_cursor_offset, but instead of reading we write data */
|
||||
offset /= 2;
|
||||
port_byte_out(REG_SCREEN_CTRL, 14);
|
||||
port_byte_out(REG_SCREEN_DATA, (unsigned char)(offset >> 8));
|
||||
port_byte_out(REG_SCREEN_CTRL, 15);
|
||||
port_byte_out(REG_SCREEN_DATA, (unsigned char)(offset & 0xff));
|
||||
}
|
||||
|
||||
void clear_screen() {
|
||||
int screen_size = MAX_COLS * MAX_ROWS;
|
||||
int i;
|
||||
char *screen = VIDEO_ADDRESS;
|
||||
|
||||
for (i = 0; i < screen_size; i++) {
|
||||
screen[i*2] = ' ';
|
||||
screen[i*2+1] = WHITE_ON_BLACK;
|
||||
}
|
||||
set_cursor_offset(get_offset(0, 0));
|
||||
}
|
||||
|
||||
|
||||
int get_offset(int col, int row) { return 2 * (row * MAX_COLS + col); }
|
||||
int get_offset_row(int offset) { return offset / (2 * MAX_COLS); }
|
||||
int get_offset_col(int offset) { return (offset - (get_offset_row(offset)*2*MAX_COLS))/2; }
|
||||
@ -0,0 +1,19 @@
|
||||
#ifndef SCREEN_H
|
||||
#define SCREEN_H
|
||||
|
||||
#define VIDEO_ADDRESS 0xb8000
|
||||
#define MAX_ROWS 25
|
||||
#define MAX_COLS 80
|
||||
#define WHITE_ON_BLACK 0x0f
|
||||
#define RED_ON_WHITE 0xf4
|
||||
|
||||
/* Screen i/o ports */
|
||||
#define REG_SCREEN_CTRL 0x3d4
|
||||
#define REG_SCREEN_DATA 0x3d5
|
||||
|
||||
/* Public kernel API */
|
||||
void clear_screen();
|
||||
void kprint_at(char *message, int col, int row);
|
||||
void kprint(char *message);
|
||||
|
||||
#endif
|
||||
@ -0,0 +1,9 @@
|
||||
#include "../cpu/isr.h"
|
||||
#include "../cpu/timer.h"
|
||||
|
||||
void main() {
|
||||
isr_install();
|
||||
|
||||
asm volatile("sti");
|
||||
init_timer(50);
|
||||
}
|
||||
@ -0,0 +1,30 @@
|
||||
#include "util.h"
|
||||
|
||||
void memory_copy(char *source, char *dest, int nbytes) {
|
||||
int i;
|
||||
for (i = 0; i < nbytes; i++) {
|
||||
*(dest + i) = *(source + i);
|
||||
}
|
||||
}
|
||||
|
||||
void memory_set(u8 *dest, u8 val, u32 len) {
|
||||
u8 *temp = (u8 *)dest;
|
||||
for ( ; len != 0; len--) *temp++ = val;
|
||||
}
|
||||
|
||||
/**
|
||||
* K&R implementation
|
||||
*/
|
||||
void int_to_ascii(int n, char str[]) {
|
||||
int i, sign;
|
||||
if ((sign = n) < 0) n = -n;
|
||||
i = 0;
|
||||
do {
|
||||
str[i++] = n % 10 + '0';
|
||||
} while ((n /= 10) > 0);
|
||||
|
||||
if (sign < 0) str[i++] = '-';
|
||||
str[i] = '\0';
|
||||
|
||||
/* TODO: implement "reverse" */
|
||||
}
|
||||
@ -0,0 +1,10 @@
|
||||
#ifndef UTIL_H
|
||||
#define UTIL_H
|
||||
|
||||
#include "../cpu/types.h"
|
||||
|
||||
void memory_copy(char *source, char *dest, int nbytes);
|
||||
void memory_set(u8 *dest, u8 val, u32 len);
|
||||
void int_to_ascii(int n, char str[]);
|
||||
|
||||
#endif
|
||||
Loading…
Reference in new issue